Verifying your theme

Oops, your theme needs a little help!

We found a price field that our auto-setup tool couldn't configure.

Our expert team can take care of it. Just click Get Expert Install and we'll send you an email when it's ready!

If everything looks okay to you, you can Ignore this warning.

Skip to content
Green Coolster Chinese ATV representing 110cc engine valve train maintenance and repair

How to Diagnose and Fix Valve Train Noise on a Chinese 110cc or 125cc Engine

A ticking or rattling noise from the top end of a Chinese ATV or dirt bike engine is one of those problems that is easy to ignore but expensive to let go. Valve train noise has several possible causes, and getting the diagnosis right before ordering parts is the difference between a quick and affordable fix and a drawn-out repair that costs significantly more than it needed to.

At Get 2 It Sales, we supply engine components for Chinese 110cc and 125cc machines regularly, and valve train questions are among the most common we receive. This guide walks through the main causes of valve train noise, how to tell them apart, and what parts to order for each scenario.

Understanding the Valve Train on a Chinese Small Engine

The valve train on a Chinese 110 cc ATV engine or 125cc dirt bike engine consists of a camshaft driven by a cam chain from the crankshaft, a rocker arm assembly that translates cam lobe movement into valve opening and closing, and the valves themselves. The cam chain runs through a tensioner and a guide to keep it taut and on track. Any wear or maladjustment in this system produces noise.

The horizontal 110cc engine used in most Chinese ATVs and the 125cc engine common in pit bikes share the same basic valve train architecture. Both use a single overhead cam, two valves per cylinder, and a manual or automatic cam chain tensioner. The differences are mainly in bore size and stroke; the valve train components are not interchangeable between the two, but the diagnostic process is identical.

A worn or stretched cam chain can create rattling or tapping noises from the top end of a Chinese dirt bike engine 

Cam Chain Stretch: The Most Common Cause

A stretched or worn cam chain is the most frequent cause of valve train noise on Chinese small engines. As the chain wears, it develops slack that the tensioner can no longer compensate for, causing the chain to slap against the guide and the timing cover. The noise is typically a light rattling or tapping that is most noticeable at idle and tends to become quieter as RPM increases.

The test is straightforward. With the engine warmed up and idling, apply the brake and blip the throttle briefly. If the noise is loudest at idle and clears slightly under load, cam chain stretch is the most likely culprit.

• Inspect the tensioner first. If the tensioner has extended to its limit and the chain still has slack, the chain itself needs replacement

• Check the cam chain guide for scoring or cracking; a worn guide accelerates chain wear and will damage a new chain if not replaced at the same time

• Always replace the cam chain and guide together rather than individually

Rocker Arm and Rocker Shaft Wear

Worn rocker arms or rocker shafts produce a persistent ticking noise that does not change much with engine speed. This is one of the most common wear points on 125cc dirt bike engine parts, particularly on machines run with low oil or that have accumulated significant hours. The rocker arm pivots on the shaft and wears an oval bore over time, which creates play and causes the tap.

To check rocker arm wear, remove the valve cover and observe the rocker arms at idle if possible, or rotate the engine by hand and check for side-to-side movement on the shaft. Any perceptible lateral play beyond a very slight amount indicates that replacement is due. Rocker arms and shafts should always be replaced as a matched set.

Blue Apollo Chinese ATV representing rocker arm and valve train component repair


Valve Clearance Out of Specification

Valve clearance is the gap between the rocker arm and the valve stem tip. When this gap is too large, the engine produces a distinct ticking noise that is consistent at idle and does not change significantly with RPM. When the gap is too tight, the valve does not fully close, which causes low compression and rough running rather than noise.

Valve clearance adjustment is a routine maintenance task on any four-stroke engine and should be checked every fifty hours of operation on Chinese small engines. The standard specification for most Chinese 110cc and 125cc engines is between zero-point-zero-eight and zero-point-twelve millimeters for both intake and exhaust valves. Always check the service documentation for the specific model before setting clearance.

• Adjustment requires removing the valve cover and rotating the engine to top dead center on the compression stroke

• Use feeler gauges to measure the existing clearance before making any adjustment

• Adjust by loosening the locknut on the rocker arm and turning the adjuster screw until the correct feeler gauge slides through with slight resistance

• Re-check clearance after tightening the locknut, as the locknut torque can shift the adjuster position




When Noise Means Something More Serious

If the valve train noise is accompanied by low compression, oil consumption, or a significant drop in power, the engine may need more than valve adjustment or chain replacement. At this stage, checking piston and cylinder wear becomes necessary before addressing the valve train. In those cases, a 125cc pit bike engine rebuild kit that includes a new piston, rings, and gasket set is the appropriate response when compression has dropped below the minimum acceptable reading alongside valve train noise.

Running an engine with a stretched cam chain past the point where the tensioner can compensate risks the chain jumping a tooth on the cam sprocket, which changes valve timing and can cause valve-to-piston contact. If the engine has been running with significant top-end noise for an extended period, a compression test should be performed before any other diagnosis to confirm that internal damage has not already occurred.

What Parts to Order and What to Check First

Affordable 110cc ATV engine parts are available from many sources, but quality matters significantly for valve train components. Rocker arms, cam chains, and valve shims that do not meet the correct dimensional tolerances will wear faster than stock and may not solve the noise problem at all. At Get 2 It Sales, every incoming shipment is inspected before it enters our inventory to verify that components match their listed specifications.

For riders sourcing Chinese ATV parts for a valve train repair, we recommend starting with a valve clearance check before ordering any components. In many cases, an adjustment resolves the noise without any parts replacement at all. If parts are needed after the check, having the correct bore size, valve stem diameter, and cam chain pitch information before ordering prevents the most common sourcing errors.

Get the Right Engine Parts From Get 2 It Sales

At Get 2 It Sales, we stock 110cc ATV engine parts and 125cc engine components for all major Chinese brands, including TaoTao, Coolster, Apollo, SSR, Kayo, and more. Our catalog covers cam chains, tensioners, cam chain guides, rocker arm assemblies, valve sets, gasket sets, and complete rebuild kits.

Our team has nearly a hundred years of combined experience in Chinese powersports, and we assist customers with part identification and fitment confirmation regularly. If you are unsure which specific component is causing the noise on your machine, or which part number is correct for your engine configuration, contact us through our website before ordering.

We carry 110cc ATV engine parts and 125cc components across every category needed for a complete valve train service, and every part ships with specifications confirmed. Get in touch with our team, and we will help you get the right part the first time.

Cart

Your cart is currently empty

Main Menu